{
    "type": "filament",
    "name": "Lofted Aero Tuned Generic Foaming TPU",
    "from": "User",
    "instantiation": "true",
    "inherits": "",
    "version": "1.9.0.0",
    "filament_settings_id": [
        "Lofted Aero Tuned Generic Foaming TPU"
    ],
    "filament_notes": "Lofted Aero Tune v1.0 | 2026-07-26 | For foaming / lightweight TPU from any vendor, tuned for RC tyres. Bed is deliberately set to 25 C (effectively off) on every plate type - bed heat collapses the foam. 3.2 mm3/s is a hard ceiling; foaming TPU jams above it. Soft filament: feed direct, never through an AMS or a long bowden path. | loftedaero.com",

    "compatible_printers": [],
    "compatible_printers_condition": "",
    "compatible_prints": [],
    "compatible_prints_condition": "",

    "filament_type": [
        "TPU"
    ],
    "filament_vendor": [
        "Generic"
    ],
    "filament_density": [
        "1.032"
    ],
    "filament_cost": [
        "50"
    ],
    "filament_diameter": [
        "1.75"
    ],
    "filament_soluble": [
        "0"
    ],
    "filament_is_support": [
        "0"
    ],
    "filament_shrink": [
        "100%"
    ],
    "temperature_vitrification": [
        "30"
    ],
    "required_nozzle_HRC": [
        "3"
    ],

    "nozzle_temperature": [
        "240"
    ],
    "nozzle_temperature_initial_layer": [
        "240"
    ],
    "nozzle_temperature_range_low": [
        "210"
    ],
    "nozzle_temperature_range_high": [
        "250"
    ],

    "cool_plate_temp": [
        "25"
    ],
    "cool_plate_temp_initial_layer": [
        "25"
    ],
    "eng_plate_temp": [
        "25"
    ],
    "eng_plate_temp_initial_layer": [
        "25"
    ],
    "textured_plate_temp": [
        "25"
    ],
    "textured_plate_temp_initial_layer": [
        "25"
    ],
    "hot_plate_temp": [
        "25"
    ],
    "hot_plate_temp_initial_layer": [
        "25"
    ],

    "filament_flow_ratio": [
        "0.5"
    ],
    "filament_max_volumetric_speed": [
        "3.2"
    ],

    "filament_retraction_length": [
        "0.01"
    ],
    "filament_retraction_speed": [
        "30"
    ],
    "filament_deretraction_speed": [
        "30"
    ],
    "filament_retract_restart_extra": [
        "0.04"
    ],
    "filament_retract_when_changing_layer": [
        "1"
    ],
    "filament_wipe": [
        "1"
    ],
    "filament_wipe_distance": [
        "1"
    ],
    "filament_z_hop": [
        "0"
    ],
    "filament_z_hop_types": [
        "Normal Lift"
    ],

    "fan_min_speed": [
        "50"
    ],
    "fan_max_speed": [
        "50"
    ],
    "fan_cooling_layer_time": [
        "1000"
    ],
    "close_fan_the_first_x_layers": [
        "1"
    ],
    "full_fan_speed_layer": [
        "4"
    ],
    "additional_cooling_fan_speed": [
        "50"
    ],
    "reduce_fan_stop_start_freq": [
        "1"
    ],
    "slow_down_for_layer_cooling": [
        "0"
    ],
    "slow_down_layer_time": [
        "10"
    ],
    "slow_down_min_speed": [
        "30"
    ],
    "enable_overhang_bridge_fan": [
        "1"
    ],
    "overhang_fan_speed": [
        "100"
    ],
    "overhang_fan_threshold": [
        "50%"
    ],

    "activate_air_filtration": [
        "0"
    ],
    "during_print_exhaust_fan_speed": [
        "70"
    ],
    "complete_print_exhaust_fan_speed": [
        "70"
    ],

    "filament_start_gcode": [
        "; filament start gcode\n"
    ],
    "filament_end_gcode": [
        "; filament end gcode\n"
    ]
}